The electrical demands on a home have changed faster than most of the wiring inside them. A house that was built to run a few lights, a refrigerator, and a television now gets asked to charge an electric vehicle overnight, run a solar inverter, and support a battery backup system, all while the original panel sits unchanged. That gap between what the wiring was designed for and what it is being asked to do is behind a large share of the calls we get in San Clemente and across the surrounding area.
We handle residential and commercial electrical work throughout the city, from a single dead outlet to a full panel upgrade and everything in between. Whether you own a home, manage a rental, or run a business that cannot afford a day without power, we take calls any hour, any day, including nights, weekends, and holidays.
Call (949) 693-6326 for a quote, and we will scope the job on the phone before anything is scheduled.
Not every power loss is a wiring problem, and figuring out which side of the meter the fault sits on is the first thing a visit covers. A utility outage shows up differently from a failed connection inside the panel. A whole-street outage, a tripped main breaker that will not reset, and a dead circuit that only affects one room are three different situations, and they point in three different directions.
When we arrive, we start at the service entrance and work inward. The goal is to confirm whether the fault is upstream of the meter, which makes it the utility's problem to fix, or downstream, which makes it ours. If it turns out to be a utility issue, we can tell you what to report and what to expect from their side. If it is on our side, we explain what it involves and what it will cost before any repair work begins.
A partial outage, where half the house has power and the other half does not, often points to a problem at the service entrance or at the utility's connection to the meter. That can look like a panel problem from the inside, and it sometimes is, but confirming which one it is before opening anything up saves time and avoids unnecessary work. We check the incoming voltage, confirm what the panel is seeing, and give you a clear answer rather than a guess.
Scheduling starts on the phone. When you call, we ask about the symptom, the circuit or area affected, and anything that changed recently, such as a new appliance, a recent storm, or a renovation that touched the wiring. That information lets us scope the job accurately and give you a price before the visit is booked.
For problems that will not wait, we take short-notice calls and work around the hour. Being local means we're easy to reach and easy to work with, and that matters when a fault shows up at night or over a weekend. We confirm what is available when you call, and we do not make promises about arrival windows we cannot keep.
Tenants and businesses that need to stay open during a visit are a common situation. We confirm ahead of time which circuits will be off and for how long, so a household or a business can plan around the work rather than being caught off guard by it. The scope is settled on the call, and nothing changes without a conversation first.
The price for electrical work depends on what the job actually involves. A straightforward outlet replacement is a different conversation from a panel upgrade or a full circuit run. What moves a quote is what the fault turns out to be, what has to be opened up to reach it, and whether the existing panel or circuit can carry the change being asked of it.
When you call, we work through those questions on the phone. A load calculation, for instance, is part of scoping any new circuit or panel work, because the answer to whether a panel can support an EV charger or a new subpanel is not a guess. We confirm the capacity, quote the work, and schedule only once the price is agreed.
No-pressure estimates, priced up front, are standard on every call. If the scope changes once the work is underway, the price is confirmed again before anything additional proceeds. You are not handed a bill at the end that does not match what was discussed at the start.
A room that was wired for a single ceiling fixture can often be opened up with a recessed lighting layout, and LED retrofits reduce energy draw without changing how the space feels. We run the circuits, install the fixtures, and confirm the dimmer compatibility where that is part of the plan. Older homes that have never had recessed lighting may need new wiring runs, and we scope that work before the visit.
Outdoor lighting covers a wide range of work. Landscape lighting circuits, motion sensor lights, security fixtures at entry points, and weatherproof outlets for patios and garages all require wiring that is run correctly for outdoor exposure. A mild coastal climate means outdoor spaces get used year-round, and the lighting that serves them needs to be installed to hold up in that environment. We handle the circuit, the conduit where it is needed, and the fixture installation in a single visit where the scope allows.
Connecting a generator to a home's wiring without a transfer switch creates a hazard for anyone working on the utility lines during an outage. A transfer switch isolates the generator from the grid and lets the home run safely on its own power. We handle the wiring from the generator connection to the transfer switch and confirm the installation meets the code requirements in this area before the job is complete. Wildfire-season public-safety power shutoffs across the region have made this a practical consideration for many households, not just a precaution.
A refrigerator, dryer, range, or EV charger pulling power from a shared circuit is a common source of tripped breakers and wiring wear. Each of those appliances draws enough current to warrant its own direct run from the panel. We check panel capacity before any circuit work is scheduled, run the dedicated circuit to the appliance location, and confirm the outlet type and amperage match what the equipment requires.
Older homes in San Clemente and across south Orange County sometimes carry knob-and-tube wiring that has reached the end of its useful life. The conductors themselves age, the insulation becomes brittle, and the system was never designed for grounding, which modern devices and circuits require. Replacement involves running new wiring through the existing wall cavities where possible, and it is scoped section by section so the disruption is managed rather than spread across the whole house at once. Wiring work is checked against code before sign-off.
Some electrical problems do not show up on demand. A circuit that trips only under load, a fault that appears in wet weather, or a light that flickers at no predictable interval are all harder to diagnose than a dead outlet with an obvious cause. We cover that work in its own section below, because finding an intermittent fault is its own kind of job. Plenty of San Clemente jobs start with a look at our page of electrical services.
Intermittent faults are the ones that take the most time to find and the most patience to explain. A breaker that trips when the air handler kicks on, a circuit that fails only after the house has been running for a few hours, or an outlet that works fine when tested but goes dead again by the next morning, none of those produce an obvious fault on arrival.
Finding the cause means tracing the circuit under the conditions that produce the symptom. That sometimes means testing under load, checking connections at every junction in the run, and measuring voltage drop across a circuit that looks fine at rest. Electrical work done to the code inspectors here enforce is the standard we hold every job to, and that applies to diagnostic work as much as to installation.
A fault that only shows up in the rain usually points to a moisture path into a junction box, a conduit seal that has failed, or a buried splice that was never properly waterproofed. Those take longer to find than a failed outlet, and the price reflects that. We explain the diagnostic process on the call so you know what the visit involves before it is scheduled.
Panel upgraded. Circuits balanced. Home powered safely.
We cover San Clemente and the communities around it throughout Orange County. San Juan Capistrano, Dana Point, Rancho Mission Viejo, Ladera Ranch, and Laguna Niguel are all part of the area we work in regularly. Calls are answered any hour, any day, and the work is carried out locally across the region.
Whether the property is a single-family home, a rental, or a commercial space, the process is the same. The job is scoped on the call, the price is confirmed before scheduling, and the work is done to the standards the code inspectors in this county enforce. If you are not sure whether your address is covered, call and we will confirm.
Permit requirements depend on the scope of the work and where it falls under local and county rules. Panel replacements and new circuit runs typically require a permit and inspection. We confirm what applies to the specific job before scheduling, so the work is done correctly from the start and the permit process does not catch anyone off guard.
Yes. Homes with solar inverters and battery storage systems have specific panel and circuit requirements, and we handle the electrical side of those setups: load calculations, dedicated circuits for inverter connections, and panel capacity checks to confirm the service can carry the added equipment. We do not install or service the solar panels or battery units themselves, but the wiring and panel work that makes them function is part of what we do.
If something stops working again after a visit, call us and describe what is happening. We treat a returning fault as something that needs to be looked at, and the process starts the same way: scope the problem on the call before anything is scheduled.
Rough-in is the stage where wiring is run through walls and ceilings before they are closed up. Trim-out is when outlets, switches, and fixtures are installed after the walls are finished. Both stages need to happen in the right order relative to the other trades, and we confirm the timing on the call when a renovation is involved.
Older homes in this part of Orange County sometimes carry knob-and-tube wiring, undersized panels, or circuits that were never grounded to current standards. The most common calls involve outlets that have lost power without a tripped breaker, panels that cannot support the load a modern home puts on them, and wiring that shows wear at junction points inside the walls. We scope the situation on the call and explain what the fix involves before anything is scheduled.
Whatever it was that made you read this far, that is the job we handle.
Call (949) 693-6326 and we will scope it on the phone, give you a price, and get it scheduled.
We are available around the clock, every day of the year. Call us and the rest is handled.
Towns a short way out: San Juan Capistrano, Laguna Niguel, Laguna Hills, Aliso Viejo.
We handle electrical repairs, installations, and upgrades for homes and businesses throughout San Clemente and the surrounding Orange County communities. Every job is scoped on the call before anything is scheduled, and the price is confirmed before work begins. Whether the need is a straightforward outlet repair or a full panel upgrade ahead of an EV charger install, the process is the same: we find out what the job involves, explain what it takes, and get it done.
Call (949) 693-6326 for a quote on any of the services below.
| Service Type | What's Included | When You Need It | What to Keep in Mind |
|---|---|---|---|
| Older-Home Rewiring | Full and partial rewiring projects, Knob-and-tube and aluminum wiring replacement, Grounding and bonding updates, Wall and ceiling access confirmed before work begins | Older Orange County homes where aging wiring creates repeated faults or fails a safety inspection | Rewiring involves opening walls or ceilings to run new conductors from the panel out. The scope and access needed are confirmed on the call before anything is scheduled. |
| Electrical Panel & Service Upgrades | 100-amp to 200-amp service upgrades, Subpanel installation, Load calculations before sizing, Room for EV and solar circuits | Homes adding EV chargers, solar, battery storage, or running out of breaker slots | Most San Clemente homes on 100-amp service hit capacity quickly once an EV charger or solar inverter is added. A 200-amp upgrade is the most common fix, and we size it for current and likely future load. |
| EV Charger Installation | Panel capacity check before install, Dedicated 240V circuit to garage or driveway, Charger location and mounting confirmed, Price confirmed on the call | San Clemente homeowners adding a Level 2 home charger for any EV | Orange County has one of the highest EV ownership rates in California. Most homes here run 200-amp service, which is usually enough for a Level 2 charger once the right dedicated circuit is in place. |
Call (949) 693-6326 and we will scope the job, confirm the price, and get the work on the calendar.
(949) 693-6326